How to Install Recessed Lighting
- 1 Cut a Hole in the Ceiling: Option A Whether you’re installing recessed lights in new construction or remodeling a room, first plan your light placement.
- 2 Cut a Hole in the Ceiling: Option B
- 3 Rough-In the Wiring
- 4 Wire the Light
- 5 Mount the Light
- 6 Add the Trim
- 7 Install Light Bulbs
How to install recessed lighting in an existing ceiling?
- Most models of recessed light housing have four clips that clamp the can to the ceiling by pushing down on top of the drywall.
- Pull the clips in so they do not protrude outside the can.
- Slip the can’s box into the hole, and then push the can body up into the hole until its flange is tight to the ceiling.
How to install downlights or recessed spotlights in your ceiling?
- Use the template provided with your light kit to draw the outline for each opening.
- Use a stud finder to make sure the holes do not overlap a joist.
- Drill a 1/4-inch hole in the ceiling at the center of the planned opening.
- If necessary, go into the attic and make sure there are no wires, pipes or ductwork behind the planned opening.
How to wire recessed lighting in finished ceiling?
- Open the light’s junction box.
- Run cables into the box and clamp them.
- Use wire stripper to strip a few inches of the cable’s insulation to reveal the interior wires.
- Next use the wire stripper to remove about 1/2-inch of insulation from each wire.
- Connect like-colored wires using UL-approved wire connectors.
How to replace recessed light with a ceiling fixture?
- Unscrew the old bulb from the recessed lighting housing.
- Remove the old trim from the outer ring of the housing.
- Squeeze the side spring clips to remove the light housing; you should see the light socket at the top of the well.
- Adjust the rear plate in the housing, by loosening the wing nut that allows the adjustment.
installing recessed lighting in ceiling
How to install downlights or recessed spotlights in your ceiling?
- Use the template provided with your light kit to draw the outline for each opening.
- Use a stud finder to make sure the holes do not overlap a joist.
- Drill a 1/4-inch hole in the ceiling at the center of the planned opening.
- If necessary, go into the attic and make sure there are no wires, pipes or ductwork behind the planned opening.
How much does it cost to install recessed lighting? Written by HomeAdvisor. Expect to pay between $100 to $480 per fixture, or $360 on average, when having recessed lighting installed by a pro. At the average price, the project runs about $2,160 for six fixtures. The total varies depending on the type of housing, trim, and bulbs you select.
How to replace recessed light with a ceiling fixture?
- Unscrew the old bulb from the recessed lighting housing.
- Remove the old trim from the outer ring of the housing.
- Squeeze the side spring clips to remove the light housing; you should see the light socket at the top of the well.
- Adjust the rear plate in the housing, by loosening the wing nut that allows the adjustment.
How to install recessed lighting in 5 steps? Step 5: Wiring Your Recessed Lights. To wire the recessed lighting in your existing ceiling, remove the junction box and switch plate on the wall where you will attach your wires. Run the light’s wire from the cutout housing location to the junction box. Make sure you leave a minimum 10-15 centimeters of extra wire on each side.
How to install recessed lighting in an existing ceiling?
How to wire recessed lighting in finished ceiling?
- Open the light’s junction box.
- Run cables into the box and clamp them.
- Use wire stripper to strip a few inches of the cable’s insulation to reveal the interior wires.
- Next use the wire stripper to remove about 1/2-inch of insulation from each wire.
- Connect like-colored wires using UL-approved wire connectors.
How difficult is it to install recessed lighting?
- Recessed lighting is easiest to install during new construction but can be retrofitted into existing ceilings.
- Placement is key.
- Wire the lights in zones for greater flexibility.
- Weigh the pros and cons of the different types of light bulbs.
- Use the right tools to cut holes in the drywall.
- Consider hiring an electrician.
How to install downlights or recessed spotlights in your ceiling?
- Use the template provided with your light kit to draw the outline for each opening.
- Use a stud finder to make sure the holes do not overlap a joist.
- Drill a 1/4-inch hole in the ceiling at the center of the planned opening.
- If necessary, go into the attic and make sure there are no wires, pipes or ductwork behind the planned opening.
How to install recessed lighting in 5 steps? Step 5: Wiring Your Recessed Lights. To wire the recessed lighting in your existing ceiling, remove the junction box and switch plate on the wall where you will attach your wires. Run the light’s wire from the cutout housing location to the junction box. Make sure you leave a minimum 10-15 centimeters of extra wire on each side.